[text] BT homehub 5 serial log

Viewer

copydownloadembedprintName: BT homehub 5 serial log
  1.  
  2. ROM VER: 1.1.4
  3. CFG 06
  4. NAND
  5. NAND Read OK
  6.  
  7. DDR autotuning Rev 0.3d
  8. DDR size from 0xa0000000 - 0xa7ffffff
  9. DDR check ok... start booting...
  10.  
  11.  
  12.  
  13. U-Boot 2010.06-LANTIQ-v-2.2.46 (Feb 11 2015 - 16:18:32 on bat@rowlf-jungo)
  14.  
  15. CLOCK CPU 500M RAM 250M
  16. secure boot
  17. DRAM:  125 MiB
  18. NAND:  ONFI flash detected
  19. ONFI param page 0 valid
  20. NAND device: Manufacturer ID: 0x01, Chip ID: 0xf1 (AMD S34ML01G1)
  21. 128 MiB
  22. Bad block table found at page 65472, version 0x01
  23. Bad block table found at page 65408, version 0x01
  24. In:    serial
  25. Out:   serial
  26. Err:   serial
  27. Net:   Internal phy(GE) firmware version: 0x841b
  28. vr9 Switch
  29.  
  30. Type "run flash_nfs" to mount root filesystem over NFS
  31.  
  32. Hit any key to stop autoboot:  0
  33. Creating 1 MTD partitions on "nand0":
  34. 0x000000100000-0x000007f80000 : "mtd=0"
  35. UBI: attaching mtd1 to ubi0
  36. UBI: physical eraseblock size:   131072 bytes (128 KiB)
  37. UBI: logical eraseblock size:    129024 bytes
  38. UBI: smallest flash I/O unit:    2048
  39. UBI: sub-page size:              512
  40. UBI: VID header offset:          512 (aligned 512)
  41. UBI: data offset:                2048
  42. UBI: attached mtd1 to ubi0
  43. UBI: MTD device name:            "mtd=0"
  44. UBI: MTD device size:            126 MiB
  45. UBI: number of good PEBs:        1012
  46. UBI: number of bad PEBs:         0
  47. UBI: max. allowed volumes:       128
  48. UBI: wear-leveling threshold:    4096
  49. UBI: number of internal volumes: 1
  50. UBI: number of user volumes:     4
  51. UBI: available PEBs:             10
  52. UBI: total number of reserved PEBs: 1002
  53. UBI: number of PEBs reserved for bad PEB handling: 10
  54. UBI: max/mean erase counter: 9/4
  55. Volume kernel found at volume id 0
  56. read 0 bytes from volume 0 to 80800000(buf address)
  57. Read [2064384] bytes
  58. ## Booting kernel from Legacy Image at 80800000 ...
  59.    Image Name:   MIPS OpenWrt Linux-4.14.156
  60.    Created:      2019-11-30  15:52:33 UTC
  61.    Image Type:   MIPS Linux Kernel Image (lzma compressed)
  62.    Data Size:    2004767 Bytes = 1.9 MiB
  63.    Load Address: 80002000
  64.    Entry Point:  80002000
  65.    Verifying Checksum ... OK
  66.    Uncompressing Kernel Image ... OK
  67.  
  68. Starting kernel ...
  69.  
  70. [    0.000000] Linux version 4.14.156 (builder@buildhost) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r10775-db8345d8e4)) #0 SMP Sat Nov 30 15:52:33 2019
  71. [    0.000000] SoC: xRX200 rev 1.2
  72. [    0.000000] bootconsole [early0] enabled
  73. [    0.000000] CPU0 revision is: 00019556 (MIPS 34Kc)
  74. [    0.000000] MIPS: machine is BT Home Hub 5A
  75. [    0.000000] Determined physical RAM map:
  76. [    0.000000]  memory: 08000000 @ 00000000 (usable)
  77. [    0.000000] Initrd not found or empty - disabling initrd
  78. [    0.000000] Detected 1 available secondary CPU(s)
  79. [    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
  80. [    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
  81. [    0.000000] Zone ranges:
  82. [    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007ffffff]
  83. [    0.000000] Movable zone start for each node
  84. [    0.000000] Early memory node ranges
  85. [    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007ffffff]
  86. [    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff]
  87. [    0.000000] random: get_random_bytes called from 0x80630740 with crng_init=0
  88. [    0.000000] percpu: Embedded 14 pages/cpu s25968 r8192 d23184 u57344
  89. [    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 32512
  90. [    0.000000] Kernel command line: console=ttyLTQ0,115200
  91. [    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
  92. [    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
  93. [    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
  94. [    0.000000] Writing ErrCtl register=00019824
  95. [    0.000000] Readback ErrCtl register=00019824
  96. [    0.000000] Memory: 121888K/131072K available (5218K kernel code, 193K rwdata, 908K rodata, 1280K init, 230K bss, 9184K reserved, 0K cma-reserved)
  97. [    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
  98. [    0.000000] Hierarchical RCU implementation.
  99. [    0.000000] NR_IRQS: 256
  100. [    0.000000] CPU Clock: 500MHz
  101. [    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041786 ns
  102. [    0.000011] sched_clock: 32 bits at 250MHz, resolution 4ns, wraps every 8589934590ns
  103. [    0.007907] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
  104. [    0.046050] pid_max: default: 32768 minimum: 301
  105. [    0.050963] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
  106. [    0.057479] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
  107. [    0.066913] Hierarchical SRCU implementation.
  108. [    0.072418] smp: Bringing up secondary CPUs ...
  109. [    0.077904] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
  110. [    0.077918] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
  111. [    0.078071] CPU1 revision is: 00019556 (MIPS 34Kc)
  112. [    0.109110] Synchronize counters for CPU 1: done.
  113. [    0.133426] smp: Brought up 1 node, 2 CPUs
  114. [    0.142567] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
  115. [    0.152237] futex hash table entries: 512 (order: 2, 16384 bytes)
  116. [    0.158520] pinctrl core: initialized pinctrl subsystem
  117. [    0.165286] NET: Registered protocol family 16
  118. [    0.180833] pinctrl-xway 1e100b10.pinmux: Init done
  119. [    0.187165] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28
  120. [    0.199299] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
  121. [    0.207323] PCI host bridge /fpi@10000000/pci@e105400 ranges:
  122. [    0.213026]  MEM 0x0000000018000000..0x0000000019ffffff
  123. [    0.218289]   IO 0x000000001ae00000..0x000000001affffff
  124. [    0.343036] PCI host bridge /fpi@10000000/pcie@d900000 ranges:
  125. [    0.374878] usbcore: registered new interface driver usbfs
  126. [    0.380539] usbcore: registered new interface driver hub
  127. [    0.385979] usbcore: registered new device driver usb
  128. [    0.391674] PCI host bridge to bus 0000:00
  129. [    0.395706] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]
  130. [    0.402624] pci_bus 0000:00: root bus resource [io  0x1ae00000-0x1affffff]
  131. [    0.409548] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
  132. [    0.416422] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
  133. [    0.425064] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]
  134. [    0.432037] PCI host bridge to bus 0000:01
  135. [    0.436064] pci_bus 0000:01: root bus resource [mem 0x1c000000-0x1cffffff]
  136. [    0.442985] pci_bus 0000:01: root bus resource [io  0x1d800000-0x1d8fffff]
  137. [    0.449909] pci_bus 0000:01: root bus resource [??? 0x00000000 flags 0x0]
  138. [    0.456785] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
  139. [    0.464849] ifx_pcie_rc_class_early_fixup: fixed pcie host bridge to pci-pci bridge
  140. [    0.483093] pci 0000:01:00.0: bridge configuration invalid ([bus 02-00]), reconfiguring
  141. [    0.492288] pci 0000:01:00.0: BAR 8: assigned [mem 0x1c000000-0x1c1fffff]
  142. [    0.499010] pci 0000:01:00.0: BAR 9: assigned [mem 0x1c200000-0x1c2fffff pref]
  143. [    0.506289] pci 0000:02:00.0: BAR 0: assigned [mem 0x1c000000-0x1c1fffff 64bit]
  144. [    0.513700] pci 0000:02:00.0: BAR 6: assigned [mem 0x1c200000-0x1c20ffff pref]
  145. [    0.520940] pci 0000:01:00.0: PCI bridge to [bus 02]
  146. [    0.525970] pci 0000:01:00.0:   bridge window [mem 0x1c000000-0x1c1fffff]
  147. [    0.532842] pci 0000:01:00.0:   bridge window [mem 0x1c200000-0x1c2fffff pref]
  148. [    0.542333] clocksource: Switched to clocksource MIPS
  149. [    0.549879] NET: Registered protocol family 2
  150. [    0.555497] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
  151. [    0.562390] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
  152. [    0.568819] TCP: Hash tables configured (established 1024 bind 1024)
  153. [    0.575392] UDP hash table entries: 256 (order: 1, 8192 bytes)
  154. [    0.581186] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
  155. [    0.587442] random: fast init done
  156. [    0.591258] NET: Registered protocol family 1
  157. [    0.596395] gptu: totally 6 16-bit timers/counters
  158. [    0.601427] gptu: misc_register on minor 63
  159. [    0.605585] gptu: succeeded to request irq 126
  160. [    0.610070] gptu: succeeded to request irq 127
  161. [    0.614591] gptu: succeeded to request irq 128
  162. [    0.619118] gptu: succeeded to request irq 129
  163. [    0.623609] gptu: succeeded to request irq 130
  164. [    0.628140] gptu: succeeded to request irq 131
  165. [    0.632807] No VPEs reserved for AP/SP, not initialize VPE loader
  166. [    0.632807] Pass maxvpes=<n> argument as kernel argument
  167. [    0.644184] No TCs reserved for AP/SP, not initializing RTLX.
  168. [    0.644184] Pass maxtcs=<n> argument as kernel argument
  169. [    0.656965] Crashlog allocated RAM at address 0x3f00000
  170. [    0.662747] workingset: timestamp_bits=30 max_order=15 bucket_order=0
  171. [    0.681976] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  172. [    0.687747] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
  173. [    0.704866] io scheduler noop registered
  174. [    0.708719] io scheduler deadline registered (default)
  175. [    0.718126] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc
  176. [    0.727058] console [ttyLTQ0] enabled
  177. [    0.727058] console [ttyLTQ0] enabled
  178. [    0.734379] bootconsole [early0] disabled
  179. [    0.734379] bootconsole [early0] disabled
  180. [    0.746228] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xf1
  181. [    0.751145] nand: AMD/Spansion S34ML01G1
  182. [    0.755069] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
  183. [    0.763254] Bad block table found at page 65472, version 0x01
  184. [    0.769279] Bad block table found at page 65408, version 0x01
  185. [    0.774455] 4 fixed-partitions partitions found on MTD device 14000000.nand
  186. [    0.781133] Creating 4 MTD partitions on "14000000.nand":
  187. [    0.786540] 0x000000000000-0x0000000a0000 : "u-boot"
  188. [    0.793202] 0x0000000a0000-0x0000000c0000 : "uboot-env"
  189. [    0.798813] 0x0000000c0000-0x000000100000 : "unused"
  190. [    0.804147] 0x000000100000-0x000007f80000 : "ubi"
  191. [    0.814893] libphy: Fixed MDIO Bus: probed
  192. [    0.822219] wdt 1f8803f0.watchdog: Init done
  193. [    0.832073] NET: Registered protocol family 10
  194. [    0.838787] Segment Routing with IPv6
  195. [    0.841136] NET: Registered protocol family 17
  196. [    0.845627] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
  197. [    0.858481] 8021q: 802.1Q VLAN Support v1.8
  198. [    0.972599] libphy: lantiq,xrx200-mdio: probed
  199. [    0.981825] net-xrx200: invalid MAC, using random
  200. [    1.054926] Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.5 / v1.6 0:00: attached PHY driver [Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.5 / v1.6] (mii_bus:phy_addr=0:00, irq=POLL)
  201. [    1.138906] Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.5 / v1.6 0:01: attached PHY driver [Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.5 / v1.6] (mii_bus:phy_addr=0:01, irq=POLL)
  202. [    1.222889] Intel XWAY PHY11G (xRX v1.2 integrated) 0:11: attached PHY driver [Intel XWAY PHY11G (xRX v1.2 integrated)] (mii_bus:phy_addr=0:11, irq=POLL)
  203. [    1.306888] Intel XWAY PHY11G (xRX v1.2 integrated) 0:13: attached PHY driver [Intel XWAY PHY11G (xRX v1.2 integrated)] (mii_bus:phy_addr=0:13, irq=POLL)
  204. [    1.390905] Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.5 / v1.6 0:05: attached PHY driver [Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.5 / v1.6] (mii_bus:phy_addr=0:05, irq=POLL)
  205. [    1.407596] UBI: auto-attach mtd3
  206. [    1.409496] ubi0: attaching mtd3
  207. [    1.560027] ubi0: scanning is finished
  208. [    1.576818] ubi0: attached mtd3 (name "ubi", size 126 MiB)
  209. [    1.580946] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes
  210. [    1.587786] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 512
  211. [    1.594495] ubi0: VID header offset: 512 (aligned 512), data offset: 2048
  212. [    1.601296] ubi0: good PEBs: 1012, bad PEBs: 0, corrupted PEBs: 0
  213. [    1.607368] ubi0: user volume: 4, internal volumes: 1, max. volumes count: 128
  214. [    1.614606] ubi0: max/mean erase counter: 9/4, WL threshold: 4096, image sequence number: 624701095
  215. [    1.623655] ubi0: available PEBs: 0, total reserved PEBs: 1012, PEBs reserved for bad PEB handling: 20
  216. [    1.633045] ubi0: background thread "ubi_bgt0d" started, PID 424
  217. [    1.637656] block ubiblock0_1: created from ubi0:1(rootfs)
  218. [    1.644503] ubiblock: device ubiblock0_1 (rootfs) set to be root files[    1.658956] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
  219. [    1.668749] Freeing unused kernel memory: 1280K
  220. [    1.671893] This architecture does not have kernel memory protection.
  221. [    2.299896] init: Console is alive
  222. [    2.302340] init: - watchdog -
  223. [    3.651323] kmodloader: loading kernel modules from /etc/modules-boot.d/*
  224. [    3.771269] dwc2 1e101000.usb: 1e101000.usb supply vusb_d not found, using dummy regulator
  225. [    3.778389] dwc2 1e101000.usb: 1e101000.usb supply vusb_a not found, using dummy regulator
  226. [    3.786865] dwc2 1e101000.usb: dwc2_core_reset() HANG! AHB Idle GRSTCTL=0
  227. [    3.994704] dwc2 1e101000.usb: DWC OTG Controller
  228. [    3.998053] dwc2 1e101000.usb: new USB bus registered, assigned bus number 1
  229. [    4.005159] dwc2 1e101000.usb: irq 62, io mem 0x1e101000
  230. [    4.012060] hub 1-0:1.0: USB hub found
  231. [    4.014594] hub 1-0:1.0: 1 port detected
  232. [    4.020652] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
  233. [    4.031863] init: - preinit -
  234. [    5.147571] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
  235. [    5.152374] lantiq,xrx200-net 1e108000.eth eth0: port 1 got link
  236. [    5.158643] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
  237. [    5.187602] random: procd: uninitialized urandom read (4 bytes read)
  238. Press the [f] key and hit [enter] to enter failsafe mode
  239. Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
  240. [    8.356138] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 493
  241. [    8.386947] UBIFS (ubi0:2): recovery needed
  242. [    8.492873] UBIFS (ubi0:2): recovery completed
  243. [    8.496154] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data"
  244. [    8.503761] UBIFS (ubi0:2): LEB size: 129024 bytes (126 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
  245. [    8.513678] UBIFS (ubi0:2): FS size: 119992320 bytes (114 MiB, 930 LEBs), journal size 6064128 bytes (5 MiB, 47 LEBs)
  246. [    8.524290] UBIFS (ubi0:2): reserved for root: 4952683 bytes (4836 KiB)
  247. [    8.530923] UBIFS (ubi0:2): media format: w5/r0 (latest is w5/r0), UUID 3FEE0112-7C48-4484-A069-F0D0675E8B20, small LPT model
  248. [    8.544439] mount_root: switching to ubifs overlay
  249. [    8.586811] urandom-seed: Seeding with /etc/urandom.seed
  250. [    8.842708] procd: - early -
  251. [    8.844351] procd: - watchdog -
  252. [    9.242349] lantiq,xrx200-net 1e108000.eth eth0: port 1 lost link
  253. [    9.519571] procd: - watchdog -
  254. [    9.521918] procd: - ubus -
  255. [    9.623109] random: ubusd: uninitialized urandom read (4 bytes read)
  256. [    9.630588] random: ubusd: uninitialized urandom read (4 bytes read)
  257. [    9.636191] random: ubusd: uninitialized urandom read (4 bytes read)
  258. [    9.644082] procd: - init -
  259. Please press Enter to activate this console.
  260. [   10.964708] kmodloader: loading kernel modules from /etc/modules.d/*
  261. [   10.973326] IFXOS, Version 1.5.19 (c) Copyright 2009, Lantiq Deutschland GmbH
  262. [   10.983973] NET: Registered protocol family 8
  263. [   10.986952] NET: Registered protocol family 20
  264. [   11.000261] PPP generic driver version 2.4.2
  265. [   11.017233] ip6_tables: (C) 2000-2006 Netfilter Core Team
  266. [   11.033974] urngd: v1.0.0 started.
  267. [   11.044851] Lantiq (VRX) DSL CPE MEI driver, version 1.5.17.6, (c) 2007-2015 Lantiq Beteiligungs-GmbH & Co. KG
  268. [   11.057621]
  269. [   11.057621]
  270. [   11.057621] Lantiq CPE API Driver version: DSL CPE API V4.17.18.6
  271. [   11.075322]
  272. [   11.075322] Predefined debug level: 3
  273. [   11.089816] Loading modules backported from Linux version v4.19.85-0-gc63ee2939dc1
  274. [   11.096016] Backport generated by backports.git v4.19.85-1-0-g8a8be258
  275. [   11.107044] ip_tables: (C) 2000-2006 Netfilter Core Team
  276. [   11.118046] Infineon Technologies DEU driver version 2.0.0
  277. [   11.125144] IFX DEU DES initialized (multiblock).
  278. [   11.130426] IFX DEU AES initialized (multiblock).
  279. [   11.134587] IFX DEU ARC4 initialized (multiblock).
  280. [   11.138940] IFX DEU SHA1 initialized.
  281. [   11.142633] IFX DEU MD5 initialized.
  282. [   11.146062] IFX DEU SHA1_HMAC initialized.
  283. [   11.150470] IFX DEU MD5_HMAC initialized.
  284. [   11.165173] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
  285. [   11.235855] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
  286. [   11.248847] owl-loader 0000:00:0e.0: fixup device configuration
  287. [   11.256964] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]
  288. [   11.268555] NET: Registered protocol family 24
  289. [   11.300923] xt_time: kernel timezone is -0000
  290. [   11.549094] random: crng init done
  291. [   11.551133] random: 6 urandom warning(s) missed due to ratelimiting
  292. [   11.588116] ifx_pcie_bios_map_irq port 0 dev 0000:02:00.0 slot 0 pin 1
  293. [   11.593401] ifx_pcie_bios_map_irq dev 0000:02:00.0 irq 144 assigned
  294. [   11.599630] ath10k 4.19 driver, optimized for CT firmware, probing pci device: 0x3c.
  295. [   11.608934] PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
  296. [   11.613378] PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
  297. [   11.619140] ath10k_pci 0000:02:00.0: pci irq legacy oper_irq_mode 1 irq_mode 0 reset_mode 0
  298. [   11.840779] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/fwcfg-pci-0000:02:00.0.txt failed with error -2
  299. [   11.849978] ath10k_pci 0000:02:00.0: Falling back to user helper
  300. [   12.062970] firmware ath10k!fwcfg-pci-0000:02:00.0.txt: firmware_loading_store: map pages failed
  301. [   12.070987] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:02:00.0.bin failed with error -2
  302. [   12.081113] ath10k_pci 0000:02:00.0: Falling back to user helper
  303. [   12.361313] firmware ath10k!pre-cal-pci-0000:02:00.0.bin: firmware_loading_store: map pages failed
  304. [   12.370710] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/ct-firmware-5.bin failed with error -2
  305. [   12.380322] ath10k_pci 0000:02:00.0: Falling back to user helper
  306. [   12.663602] firmware ath10k!QCA988X!hw2.0!ct-firmware-5.bin: firmware_loading_store: map pages failed
  307. [   12.672071] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/ct-firmware-2.bin failed with error -2
  308. [   12.682459] ath10k_pci 0000:02:00.0: Falling back to user helper
  309. [   12.963286] firmware ath10k!QCA988X!hw2.0!ct-firmware-2.bin: firmware_loading_store: map pages failed
  310. [   12.971601] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-6.bin failed with error -2
  311. [   12.981916] ath10k_pci 0000:02:00.0: Falling back to user helper
  312. [   13.265538] firmware ath10k!QCA988X!hw2.0!firmware-6.bin: firmware_loading_store: map pages failed
  313. [   13.273747] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-5.bin failed with error -2
  314. [   13.283869] ath10k_pci 0000:02:00.0: Falling back to user helper
  315. [   13.564196] firmware ath10k!QCA988X!hw2.0!firmware-5.bin: firmware_loading_store: map pages failed
  316. [   13.572362] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-4.bin failed with error -2
  317. [   13.582513] ath10k_pci 0000:02:00.0: Falling back to user helper
  318. [   13.863516] firmware ath10k!QCA988X!hw2.0!firmware-4.bin: firmware_loading_store: map pages failed
  319. [   13.871592] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/firmware-3.bin failed with error -2
  320. [   13.881884] ath10k_pci 0000:02:00.0: Falling back to user helper
  321. [   14.165977] firmware ath10k!QCA988X!hw2.0!firmware-3.bin: firmware_loading_store: map pages failed
  322. [   14.178810] ath10k_pci 0000:02:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000
  323. [   14.186748] ath10k_pci 0000:02:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
  324. [   14.203597] ath10k_pci 0000:02:00.0: firmware ver 10.1-ct-8x-__fW-022-64cc8007 api 2 features wmi-10.x,has-wmi-mgmt-tx,mfp,txstatus-noack,wmi-10.x-CT,ratemask-CT,txrate-CT,get-temp-CT,tx-rc-CT,cust-stats-CT,retry-gt2-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT crc32 156478f0
  325. [   14.254580] ath10k_pci 0000:02:00.0: Direct firmware load for ath10k/QCA988X/hw2.0/board-2.bin failed with error -2
  326. [   14.263665] ath10k_pci 0000:02:00.0: Falling back to user helper
  327. [   14.521045] firmware ath10k!QCA988X!hw2.0!board-2.bin: firmware_loading_store: map pages failed
  328. [   14.529237] ath10k_pci 0000:02:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08
  329. [   15.409902] ath10k_pci 0000:02:00.0: 10.1 wmi init: vdevs: 16  peers: 127  tid: 256
  330. [   15.425196] ath10k_pci 0000:02:00.0: wmi print 'P 128 V 8 T 410'
  331. [   15.429821] ath10k_pci 0000:02:00.0: wmi print 'msdu-desc: 1424  sw-crypt: 0 ct-sta: 0'
  332. [   15.438206] ath10k_pci 0000:02:00.0: wmi print 'alloc rem: 20904 iram: 26072'
  333. [   15.488139] ath10k_pci 0000:02:00.0: htt-ver 2.1 wmi-op 2 htt-op 2 cal file max-sta 128 raw 0 hwcrypto 1
  334. [   15.501138] ath10k_pci 0000:02:00.0: NOTE:  Firmware DBGLOG output disabled in debug_mask: 0x10000000
  335. [   15.650520] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
  336. [   15.661470] ath: phy1: Ignoring endianness difference in EEPROM magic bytes.
  337. [   15.694732] ieee80211 phy1: Atheros AR9287 Rev:2 mem=0xb8000000, irq=30
  338. [   15.701110] kmodloader: done loading kernel modules from /etc/modules.d/*
  339. [   28.258675] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
  340. [   28.290756] device eth0 entered promiscuous mode
  341. [   28.294910] br-lan: port 1(eth0.1) entered blocking state
  342. [   28.299482] br-lan: port 1(eth0.1) entered disabled state
  343. [   28.305437] device eth0.1 entered promiscuous mode
  344. [   28.314758] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
  345. [   30.635345] ath: EEPROM regdomain: 0x812c
  346. [   30.637910] ath: EEPROM indicates we should expect a country code
  347. [   30.644086] ath: doing EEPROM country->regdmn map search
  348. [   30.649431] ath: country maps to regdmn code: 0x37
  349. [   30.654218] ath: Country alpha2 being used: GR
  350. [   30.658648] ath: Regpair used: 0x37
  351. [   30.662039] ath: regdomain 0x812c dynamically updated by user
  352. [   30.668036] ath: EEPROM regdomain: 0x812c
  353. [   30.671853] ath: EEPROM indicates we should expect a country code
  354. [   30.677981] ath: doing EEPROM country->regdmn map search
  355. [   30.683297] ath: country maps to regdmn code: 0x37
  356. [   30.688066] ath: Country alpha2 being used: GR
  357. [   30.692516] ath: Regpair used: 0x37
  358. [   30.696015] ath: regdomain 0x812c dynamically updated by user
  359. [   31.396978] lantiq,xrx200-net 1e108000.eth eth0: port 1 got link
  360. [   31.401827] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
  361. [   31.410468] br-lan: port 1(eth0.1) entered blocking state
  362. [   31.414571] br-lan: port 1(eth0.1) entered forwarding state
  363. [   31.422577] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
  364.  

Editor

You can edit this paste and save as new:


File Description
  • BT homehub 5 serial log
  • Paste Code
  • 17 May-2021
  • 22.55 Kb
You can Share it: