[text] s905x bricked

Viewer

copydownloadembedprintName: s905x bricked
  1. GXL:BL1:9ac50e:a1974b;FEAT:ADFC318C;POC:3;RCY:0;EMMC:0;READ:0;CHK:AA;SD:0;READ:0;0.0;CHK:0;
  2. no sdio debug board detected
  3. TE: 274768
  4.  
  5. BL2 Built : 11:58:42, May 27 2017.
  6. gxl gc3c9a84 - xiaobo.gu@droid05
  7.  
  8. set vcck to 1120 mv
  9. set vddee to 1000 mv
  10. Board ID = 1
  11. CPU clk: 1200MHz
  12. DQS-corr enabled
  13. DDR scramble enabled
  14. DDR3 chl: Rank0+1 @ 912MHz - PASS
  15. Rank0: 1024MB(auto)-2T-13
  16. Rank1: 1024MB(auto)-2T-13
  17. DataBus test pass!
  18. AddrBus test pass!
  19. Load fip header from SD, src: 0x0000c200, des: 0x01400000, size: 0x00004000
  20. New fip structure!
  21. Load bl30 from SD, src: 0x00010200, des: 0x01100000, size: 0x0000d600
  22. Load bl31 from SD, src: 0x00020200, des: 0x05100000, size: 0x00018400
  23. Load bl33 from SD, src: 0x0003c200, des: 0x01000000, size: 0x0003f800
  24. NOTICE:  BL3-1: v1.0(release):3348978
  25. NOTICE:  BL3-1: Built : 15:44:01, May 12 2017
  26. [BL31]: GXL CPU setup!
  27. NOTICE:  BL3-1: BL33 decompress pass
  28. mpu_config_enable:ok
  29. [Image: gxl_v1.1.3221-2cfba69 2017-05-27 16:03:58 qiufang.dai@droid07]
  30. OPS=0x82
  31. cc 7 a9 a3 8d 54 69 a5 75 9 6e b4 [0.519148 Inits done]
  32. secure task start!
  33. high task start!
  34. low task start!
  35. ERROR:   Error initializing runtime service opteed_fast
  36.  
  37.  
  38. U-Boot 2015.01 (May 04 2019 - 17:29:57), Build: jenkins-LePotato-322
  39.  
  40. DRAM:  2 GiB
  41. Relocation Offset is: 76f30000
  42. register usb cfg[0][1] = 0000000077f92318
  43. [CANVAS]canvas init
  44. vpu: clk_level = 7
  45. vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
  46. vpu: vpu_clk_gate_init_off
  47. vpp: vpp_init
  48. MMC:   aml_priv->desc_buf = 0x0000000073f30640
  49. aml_priv->desc_buf = 0x0000000073f32960
  50. emmc/sd response timeout, cmd8, status=0x3ff2800
  51. emmc/sd response timeout, cmd55, status=0x3ff2800
  52. [mmc_init] mmc init success
  53. SDIO Port B: 0, SDIO Port C: 1
  54. Using default environment
  55.  
  56. In:    serial
  57. Out:   serial
  58. Err:   serial
  59. hpd_state=0
  60. cvbs performance type = 6, table = 0
  61. Net:   dwmac.c9410000
  62. Warning: dwmac.c9410000 MAC addresses is not from dtb
  63.  
  64. [OSD]check dts: FDT_ERR_BADMAGIC, load default fb_addr parameters
  65. [OSD]fb_addr for logo: 0x3d800000
  66. [OSD]check dts: FDT_ERR_BADMAGIC, load default fb_addr parameters
  67. [OSD]fb_addr for logo: 0x3d800000
  68. [CANVAS]addr=0x3d800000 width=3840, height=2160
  69. Hit Enter or space or Ctrl+C key to stop autoboot -- :  0
  70. card in
  71. init_part() 278: PART_TYPE_DOS
  72. [mmc_init] mmc init success
  73. reading boot.ini
  74. 1460 bytes read in 3 ms (474.6 KiB/s)
  75. cfgload: applying boot.ini...
  76. cfgload: setenv bootrootfs "BOOT_IMAGE=kernel.img boot=UUID=0405-0637 disk=UUID=077f0773-4d14-47dd-9c5c-d73a1134aa1c"
  77. cfgload: setenv condev "ttyS0,115200"
  78. cfgload: setenv hdmimode "1080p60hz"
  79. cfgload: setenv hdmioutput   "1"
  80. cfgload: setenv vpu          "1"
  81. cfgload: setenv libreelec "quiet"
  82. cfgload: setenv hdmi_cec "1"
  83. cfgload: setenv uenv_addr 0x13000000
  84. cfgload: fatload mmc 0:1 ${loadaddr} kernel.img
  85. reading kernel.img
  86. 9631744 bytes read in 549 ms (16.7 MiB/s)
  87. cfgload: fatload mmc 0:1 ${dtb_mem_addr} dtb.img
  88. reading dtb.img
  89. 90112 bytes read in 8 ms (10.7 MiB/s)
  90. cfgload: if fatload mmc 0:1 ${uenv_addr} config.ini; then env import -t ${uenv_addr} $filesize; fi
  91. reading config.ini
  92. 2309 bytes read in 4 ms (563.5 KiB/s)
  93. cfgload: setenv libretech "no_console_suspend logo=osd1,loaded,0x3f800000,${hdmimode} vout=${hdmimode},enable hdmimode=${hdmimode} cvbsmode=nocvbs consoleblank=0"
  94. cfgload: if test "${hdmi_cec}" = "1"; then setenv cec "hdmitx=cec17"; fi
  95. cfgload: setenv bootargs "console=${condev} ${bootrootfs} ${libretech} ${cec} ${libreelec}"
  96. cfgload: bootm start
  97. ## Booting Android Image at 0x01080000 ...
  98. reloc_addr =73f4d190
  99. copy done
  100. load dtb from 0x1000000 ......
  101.       Amlogic multi-dtb tool
  102.       Multi dtb detected
  103.       Multi dtb tool version: v2 .
  104.       Support 2 dtbs.
  105.         aml_dt soc: gxl platform: p212 variant: 2g
  106.         dtb 0 soc: gxl   plat: p212   vari: 1g
  107.         dtb 1 soc: gxl   plat: p212   vari: 2g
  108.       Find match dtb: 1
  109. [rsvmem] no check for rsvmem, should check int kernel
  110. cfgload: bootm loados
  111.    Uncompressing Kernel Image ... OK
  112.    kernel loaded at 0x01080000, end = 0x01a89b18
  113. [rsvmem] no check for rsvmem, should check int kernel
  114. cfgload: bootm fdt
  115. [rsvmem] no check for rsvmem, should check int kernel
  116.    Loading Device Tree to 000000001fff2000, end 000000001ffff8bc ... OK
  117. cfgload: if test "${vpu}" = "0"; then fdt rm /mesonstream; fdt rm /vdec; fdt rm /ppmgr; fi
  118. cfgload: if test "${hdmioutput}" = "0"; then fdt rm /mesonfb; fi
  119. cfgload: fdt rm /partitions
  120. libfdt fdt_path_offset() returned FDT_ERR_NOTFOUND
  121. cfgload: bootm prep
  122. [rsvmem] no check for rsvmem, should check int kernel
  123.    Loading Ramdisk to 73af1000, end 73f1de00 ... OK
  124.    Loading Device Tree to 000000001ffe1000, end 000000001fff18bc ... OK
  125. cfgload: bootm go
  126. [rsvmem] no check for rsvmem, should check int kernel
  127.  
  128. Starting kernel ...
  129.  
  130. uboot time: 2219909 us
  131. domain-0 init dvfs: 4
  132. [    0.000000@0] Reserved memory: incorrect alignment of CMA region
  133. [    0.000000@0] vout_serve: set_vout_init_vmode: 1080p60hz
  134. [    0.036449@0] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xb8)
  135. [    0.036473@0] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xb8)
  136. [    0.036610@0] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xb8)
  137. [    0.036627@0] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xb8)
  138. [    0.044307@0] tv_vout: chrdev devno 266338304 for disp
  139. [    0.340980@1] amlogic-new-usb3 d0078080.usb3phy: This phy has no usb port
  140. [    0.399991@1] get_storage_dev return 1
  141. [    0.690480@2] DI-di_probe: get flag_cma error.
  142. [    0.692371@2] PPMGRDRV: err: ppmgr_driver_probe called
  143. [    1.119380@2] cectx aocec: aml_cec_probe(): no hdmirx reg resource
  144. [    1.119923@2] cectx aocec: aml_cec_probe(): no hhi reg resource
  145. [    1.339623@2] aml_snd_m8_card aml_m8_snd.49: ASoC: no source widget found for LOUTL
  146. [    1.341654@2] aml_snd_m8_card aml_m8_snd.49: ASoC: Failed to add route LOUTL -> direct -> Ext Spk
  147. [    1.350440@2] aml_snd_m8_card aml_m8_snd.49: ASoC: no source widget found for LOUTR
  148. [    1.358031@2] aml_snd_m8_card aml_m8_snd.49: ASoC: Failed to add route LOUTR -> direct -> Ext Spk
  149. [    2.075515@2] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
  150. [   34.644378@0] reboot: Restarting system(reboot)
  151. bl31 reboot reason: 0xd
  152. bl31 reboot reason: 0x1
  153. system cmd  1.
  154. GXL:BL1:9ac50e:a1974b;FEAT:ADFC318C;POC:3;RCY:0;EMMC:0;READ:0;CHK:AA;SD:0;READ:0;0.0;CHK:0;
  155. no sdio debug board detected
  156. TE: 109180
  157.  
  158. BL2 Built : 11:58:42, May 27 2017.
  159. gxl gc3c9a84 - xiaobo.gu@droid05
  160.  
  161. set vcck to 1120 mv
  162. set vddee to 1000 mv
  163. Board ID = 1
  164. CPU clk: 1200MHz
  165. DQS-corr enabled
  166. DDR scramble enabled
  167. DDR3 chl: Rank0+1 @ 912MHz - PASS
  168. Rank0: 1024MB(auto)-2T-13
  169. Rank1: 1024MB(auto)-2T-13
  170. DataBus test pass!
  171. AddrBus test pass!
  172. Load fip header from SD, src: 0x0000c200, des: 0x01400000, size: 0x00004000
  173. New fip structure!
  174. Load bl30 from SD, src: 0x00010200, des: 0x01100000, size: 0x0000d600
  175. Load bl31 from SD, src: 0x00020200, des: 0x05100000, size: 0x00018400
  176. Load bl33 from SD, src: 0x0003c200, des: 0x01000000, size: 0x0003f800
  177. NOTICE:  BL3-1: v1.0(release):3348978
  178. NOTICE:  BL3-1: Built : 15:44:01, May 12 2017
  179. [BL31]: GXL CPU setup!
  180. NOTICE:  BL3-1: BL33 decompress pass
  181. mpu_config_enable:ok
  182. [Image: gxl_v1.1.3221-2cfba69 2017-05-27 16:03:58 qiufang.dai@droid07]
  183. OPS=0x82
  184. cc 7 a9 a3 8d 54 69 a5 75 9 6e b4 [0.352746 Inits done]
  185. secure task start!
  186. high task start!
  187. low task start!
  188. ERROR:   Error initializing runtime service opteed_fast
  189.  
  190.  
  191. U-Boot 2015.01 (May 04 2019 - 17:29:57), Build: jenkins-LePotato-322
  192.  
  193. DRAM:  2 GiB
  194. Relocation Offset is: 76f30000
  195. register usb cfg[0][1] = 0000000077f92318
  196. [CANVAS]canvas init
  197. vpu: clk_level = 7
  198. vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
  199. vpu: vpu_clk_gate_init_off
  200. vpp: vpp_init
  201. MMC:   aml_priv->desc_buf = 0x0000000073f30640
  202. aml_priv->desc_buf = 0x0000000073f32960
  203. emmc/sd response timeout, cmd8, status=0x3ff2800
  204. emmc/sd response timeout, cmd55, status=0x3ff2800
  205. [mmc_init] mmc init success
  206. SDIO Port B: 0, SDIO Port C: 1
  207. Using default environment
  208.  
  209. In:    serial
  210. Out:   serial
  211. Err:   serial
  212. hpd_state=0
  213. cvbs performance type = 6, table = 0
  214. Net:   dwmac.c9410000
  215. Warning: dwmac.c9410000 MAC addresses is not from dtb
  216.  
  217. [OSD]check dts: FDT_ERR_BADMAGIC, load default fb_addr parameters
  218. [OSD]fb_addr for logo: 0x3d800000
  219. [OSD]check dts: FDT_ERR_BADMAGIC, load default fb_addr parameters
  220. [OSD]fb_addr for logo: 0x3d800000
  221. [CANVAS]addr=0x3d800000 width=3840, height=2160
  222. Hit Enter or space or Ctrl+C key to stop autoboot -- :  0
  223. card in
  224. init_part() 278: PART_TYPE_DOS
  225. [mmc_init] mmc init success
  226. reading boot.ini
  227. 1460 bytes read in 3 ms (474.6 KiB/s)
  228. cfgload: applying boot.ini...
  229. cfgload: setenv bootrootfs "BOOT_IMAGE=kernel.img boot=UUID=0405-0637 disk=UUID=077f0773-4d14-47dd-9c5c-d73a1134aa1c"
  230. cfgload: setenv condev "ttyS0,115200"
  231. cfgload: setenv hdmimode "1080p60hz"
  232. cfgload: setenv hdmioutput   "1"
  233. cfgload: setenv vpu          "1"
  234. cfgload: setenv libreelec "quiet"
  235. cfgload: setenv hdmi_cec "1"
  236. cfgload: setenv uenv_addr 0x13000000
  237. cfgload: fatload mmc 0:1 ${loadaddr} kernel.img
  238. reading kernel.img
  239. 9631744 bytes read in 549 ms (16.7 MiB/s)
  240. cfgload: fatload mmc 0:1 ${dtb_mem_addr} dtb.img
  241. reading dtb.img
  242. 90112 bytes read in 8 ms (10.7 MiB/s)
  243. cfgload: if fatload mmc 0:1 ${uenv_addr} config.ini; then env import -t ${uenv_addr} $filesize; fi
  244. reading config.ini
  245. 2309 bytes read in 4 ms (563.5 KiB/s)
  246. cfgload: setenv libretech "no_console_suspend logo=osd1,loaded,0x3f800000,${hdmimode} vout=${hdmimode},enable hdmimode=${hdmimode} cvbsmode=nocvbs consoleblank=0"
  247. cfgload: if test "${hdmi_cec}" = "1"; then setenv cec "hdmitx=cec17"; fi
  248. cfgload: setenv bootargs "console=${condev} ${bootrootfs} ${libretech} ${cec} ${libreelec}"
  249. cfgload: bootm start
  250. ## Booting Android Image at 0x01080000 ...
  251. reloc_addr =73f4d190
  252. copy done
  253. load dtb from 0x1000000 ......
  254.       Amlogic multi-dtb tool
  255.       Multi dtb detected
  256.       Multi dtb tool version: v2 .
  257.       Support 2 dtbs.
  258.         aml_dt soc: gxl platform: p212 variant: 2g
  259.         dtb 0 soc: gxl   plat: p212   vari: 1g
  260.         dtb 1 soc: gxl   plat: p212   vari: 2g
  261.       Find match dtb: 1
  262. [rsvmem] no check for rsvmem, should check int kernel
  263. cfgload: bootm loados
  264.    Uncompressing Kernel Image ... OK
  265.    kernel loaded at 0x01080000, end = 0x01a89b18
  266. [rsvmem] no check for rsvmem, should check int kernel
  267. cfgload: bootm fdt
  268. [rsvmem] no check for rsvmem, should check int kernel
  269.    Loading Device Tree to 000000001fff2000, end 000000001ffff8bc ... OK
  270. cfgload: if test "${vpu}" = "0"; then fdt rm /mesonstream; fdt rm /vdec; fdt rm /ppmgr; fi
  271. cfgload: if test "${hdmioutput}" = "0"; then fdt rm /mesonfb; fi
  272. cfgload: fdt rm /partitions
  273. libfdt fdt_path_offset() returned FDT_ERR_NOTFOUND
  274. cfgload: bootm prep
  275. [rsvmem] no check for rsvmem, should check int kernel
  276.    Loading Ramdisk to 73af1000, end 73f1de00 ... OK
  277.    Loading Device Tree to 000000001ffe1000, end 000000001fff18bc ... OK
  278. cfgload: bootm go
  279. [rsvmem] no check for rsvmem, should check int kernel
  280.  
  281. Starting kernel ...
  282.  
  283. uboot time: 2053492 us
  284. domain-0 init dvfs: 4
  285. [    0.000000@0] Reserved memory: incorrect alignment of CMA region
  286. [    0.000000@0] vout_serve: set_vout_init_vmode: 1080p60hz
  287. [    0.036388@0] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xb8)
  288. [    0.036411@0] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xb8)
  289. [    0.036546@0] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xb8)
  290. [    0.036562@0] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xb8)
  291. [    0.043988@0] tv_vout: chrdev devno 266338304 for disp
  292. [    0.334982@1] amlogic-new-usb3 d0078080.usb3phy: This phy has no usb port
  293. [    0.393059@1] get_storage_dev return 1
  294. [    0.686640@0] DI-di_probe: get flag_cma error.
  295. [    0.688508@0] PPMGRDRV: err: ppmgr_driver_probe called
  296. [    1.115467@0] cectx aocec: aml_cec_probe(): no hdmirx reg resource
  297. [    1.116005@0] cectx aocec: aml_cec_probe(): no hhi reg resource
  298. [    1.335644@0] aml_snd_m8_card aml_m8_snd.49: ASoC: no source widget found for LOUTL
  299. [    1.337674@0] aml_snd_m8_card aml_m8_snd.49: ASoC: Failed to add route LOUTL -> direct -> Ext Spk
  300. [    1.346460@0] aml_snd_m8_card aml_m8_snd.49: ASoC: no source widget found for LOUTR
  301. [    1.354053@0] aml_snd_m8_card aml_m8_snd.49: ASoC: Failed to add route LOUTR -> direct -> Ext Spk
  302. [    2.071543@0] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
  303. LibreELEC:~ # [BL31]: tee size: 0
  304.  
  305. LibreELEC:~ # ls /dev/mmc*
  306. /dev/mmcblk0       /dev/mmcblk0boot1  /dev/mmcblk1       /dev/mmcblk1p2
  307. /dev/mmcblk0boot0  /dev/mmcblk0rpmb   /dev/mmcblk1p1
  308. LibreELEC:~ # ls /dev/
  309. SYSTEM              lirc0               sw_sync             tty5
  310. amaudio             log                 tty                 tty50
  311. amaudio_ctl         loop-control        tty0                tty51
  312. amaudio_utils       loop0               tty1                tty52
  313. amhdmitx0           loop1               tty10               tty53
  314. amstream_abuf       loop2               tty11               tty54
  315. amstream_hevc       loop3               tty12               tty55
  316. amstream_mpps       loop4               tty13               tty56
  317. amstream_mpts       loop5               tty14               tty57
  318. amstream_rm         loop6               tty15               tty58
  319. amstream_sub        loop7               tty16               tty59
  320. amstream_sub_read   mali                tty17               tty6
  321. amstream_userdata   media               tty18               tty60
  322. amstream_vbuf       media.amports       tty19               tty61
  323. amsubtitle          media.audio         tty2                tty62
  324. amvecm              media.codec_mm      tty20               tty63
  325. amvideo             media.decoder       tty21               tty7
  326. amvideo_poll        media.parser        tty22               tty8
  327. amvideocap0         media.tsync         tty23               tty9
  328. aocec               media.vfm           tty24               ttyS0
  329. ashmem              media.video         tty25               ttyS1
  330. audiodsp0           mem                 tty26               ttyprintk
  331. autofs              mmcblk0             tty27               tv
  332. block               mmcblk0boot0        tty28               ubi_ctrl
  333. btrfs-control       mmcblk0boot1        tty29               uhid
  334. bus                 mmcblk0rpmb         tty3                uinput
  335. char                mmcblk1             tty30               uio0
  336. console             mmcblk1p1           tty31               unifykeys
  337. cpu_dma_latency     mmcblk1p2           tty32               urandom
  338. di0                 mqueue              tty33               vcs
  339. disk                net                 tty34               vcs1
  340. display             network_latency     tty35               vcs2
  341. efuse               network_throughput  tty36               vcs3
  342. esm_rx              null                tty37               vcs4
  343. fb0                 ppmgr               tty38               vcs5
  344. fb1                 ppp                 tty39               vcs6
  345. fd                  ptmx                tty4                vcsa
  346. full                pts                 tty40               vcsa1
  347. fuse                random              tty41               vcsa2
  348. ge2d                rfkill              tty42               vcsa3
  349. hwrng               rtc                 tty43               vcsa4
  350. i2c-0               rtc0                tty44               vcsa5
  351. initctl             shm                 tty45               vcsa6
  352. input               snd                 tty46               vfm
  353. ion                 stderr              tty47               video10
  354. kmem                stdin               tty48               wifi_power
  355. kmsg                stdout              tty49               zero
  356. LibreELEC:~ #
  357.  

Editor

You can edit this paste and save as new:


File Description
  • s905x bricked
  • Paste Code
  • 17 Mar-2021
  • 15.64 Kb
You can Share it: